Did you know?

A factory reset will delete all codes associated with the lock. 1. Make sure the door is open and unlocked. 2. Press and hold the program button for 30 seconds using the SmartKey tool or a paper clip. You will hear one long beep. 3. Press and release the program button. You will hear one short beep.Technical Support 11 / 13 ©2014 Kwikset Corporation 1-866-863-6584... Page 12 See page 9. Perform the door handing process, following the instructions inside the installation guide. The battery is too low to lock the door. Remove the batteries and replace with a fresh set. Technical Support 12 / 13 ©2014 Kwikset Corporation 1-866-863-6584...1) A programming code enables you to make changes without needing to access the programming button. This is ideal for landlords to allow programming from the outside, without access to the interior program button.Easily replaces any standard deadbolt. Featuring SmartKey Security™, which protects against advanced break-in techniques and allows you to re-key your lock yourself in seconds. SmartKey Security™ re-key technology is compatible with Kwikset (KW1) keyway. SmartKey cylinders feature a stainless steel side locking bar, racks and pins for ...WARNING: For security reasons, the first 4 digits of each user code must be unique. For example you are unable to program a user code 1-2-3-4-5 as well as a user code 1-2-3-4-6. 5) Press the Kwikset buttonExtended wireless range and superior 128-bit wireless encryption. Up to 30 user access codes for family and guests to use at the door. Secured keyless entry convenience. One touch locking. Dramatically reduced interior size and sleek metal design. 30 user codes plus master code feature for added security. 5 digit keypad with dedicated lock button.How to add/remove my Z-Wave system to my 910S Signature Series Deadbolt? Adding the lock to the network. During the pairing process, press button "A" on the lock interior once. Removing the lock from the network. Follow your smart home system's instructions to remove the lock from the network. When prompted by the system, press button A ...This bundle includes the Kwikset 909 electronic deadbolt, one Avalon Handle, and two Tustin Levers ; Backlit keyless entry touchpad with a motorized deadbolt and sleek interior; includes traditional key functionality for peace of mindOn my Smartcode 909/910, the latch bolt is not moving in the correct direction and the turnpiece will not rotate. The door handing process was not executed during installation, and the lock does not know the orientation of the doorPerform the door handing process:1. Remove battery pack by unscrewing interior. 2.Secured keyless entry convenience. One touch locking. Dramatically reduced interior size and sleek metal design. 16 user codes plus master code feature for added security. 10 digit backlit keypad with dedicated …Apr 20, 2017 ... Kwikset SmartCode 909-910: Programming Without a Mastercode ... Kwikset Smart code ... Smartcode Kwikset 916 - How to create and delete a master ...This step will teach your lock the orientation of your door and is crucial to lock operation. 1. Install 4 AA batteries in battery pack. 2. Press and HOLD the Lock button while installing battery pack. Hold button until the latch bolt starts moving on its own. 3. Did the latch bolt retract and extend on its own when the battery pack was installed?Make sure the user code is not a duplicate and that it is between 4 and 8 digits during your next attempt. Make sure the lock has room for an additional code. If all user codes are filled, delete a code to make room for this one. Make sure to enter a valid Mastercode in step 3.7.This is a short and simple video of how to change the batteries on your Kwikset SmartCode 916 Touchscreen Electronic Deadbolt. You may be trying to slide the...Remove the battery pack from the lock. Press the "Program" button for 5 seconds and then the "A" button for 5 seconds. If TS (touchscreen controller) shows low battery trouble for the lock subjected to the firmware update then install new batteries in pack. Replace the battery pack into the lock.1. Remove battery pack. 2. Press and HOLD the Program button while reinserting the battery pack. Keep holding the button for 30 seconds until the lock beeps and the status LED flashes red. 3. Press the Program button once more. The status LED will flash green and red several times. 4.Door handing instructions: 1. Remove the battery cover. 2. Remove the battery pack from the lock. 3. While holding the Program button, reinsert the battery pack, then release the Program button. 4. Press the Program button once more, and the lock will go through the door handing process. The bolt will drive excessively in both directions.How do I delete a single user code on my SmartCode 909/910 deadbolt or 911/912 lever? Deleting a user code In order to delete a user code, you must override the code by adding a different user code in the same position. ... Kwikset SmartCode 911-912: Programming Without a Mastercode. Video

Tools Needed. Ruler. Screwdriver. Note: You may also need the additional tools below, depending on your door. Wood Block. Hammer.If you wish to delete the user code, you might want to do a system or factory reset to your SmartCode 909. That is because you cannot delete lock codes for this model, but you can change them. So if you only want to override the previous code for safety or convenience purposes, then you can just add a different user code on the lock …How to delete a/all user code(s) on my Smartcode touchscreen? Deleting a Single User Code with the Mastercode DisabledNote: All codes may be deleted at once if the mastercode is enabled. For more information about the mastercode, consult the online Programming and Troubleshooting Guide.1. Keep door open. Press Program button once.2.Kwikset warrants to the Purchaser that Kwikset Products will be free from electronic defects under normal use for one (1) year from the date of purchase, as long as said Purchaser occupies the residential premises upon which the Product was originally installed ("Warranty Period"). This Electronic Limited Warranty applies only to Products ...Open the Premis App > Select the lock > click on user icon (upper right) 2. Enter the user name. 3. Enter a user code or click on "Generate Random Code" > click on Submit. Add: User code must be between 4-8 digits. 4. Change "Access Type" as required. For countries outside the U.S. and Canada, please visit our International contact page.

Please try these troubleshooting steps: 1. Start with the door open, set the lock to the “unlocked” position, and remove the battery cover. Remove all the batteries and replace them with a fresh new set. For best performance, we highly recommend alkaline batteries from a major brand (Energizer, Duracell, or Rayovac).If your Kwikset Powerbolt 2 Electronic Deadbolt isn't working properly, resetting it is usually a go-to troubleshooting step.A reset will restore the factory...…

Reader Q&A - also see RECOMMENDED ARTICLES & FAQs. How do I set up the back-lit keypad on my SmartCode 909. Possible cause: Deleting and Resetting Codes. To delete an existing user code, you’ll .